六層5500平米框架結構辦公樓設計(建筑設計,結構設計,施工組織)☆(含cad建筑圖7張,結構圖8張,橫道圖,平面布置圖,計算書47000字)
摘 要
本工程為辦公樓,由主管部門批準的新建建筑規劃以及其地理位置,建筑平面布置成“一”型。該辦公樓主體結構采用鋼筋混凝土現澆框架結構,柱網尺寸為4.8m×6m ,總長度為59.57m,總寬度為15.77m, 總高度為24.25m,占地面積為939.42平方米左右,總建筑面積為5522.139平方米,共六層,首層層高均為3.9m,其余各層層高3.6m。
外墻采用300mm厚空心磚水泥砌塊;樓梯間墻為200mm實心砌塊; 內墻采用200mm厚空心水泥砌塊。柱子采用450mm×450mm方形柱,每層的柱子截面尺寸一樣。梁的截面高度由其跨度確定,考慮到施工便利,邊跨主梁尺寸為250mm×500mm,中跨主梁采用250㎜×400㎜,無次梁,所用鋼筋為HPB235及HRB335級,梁板混凝土為C30,柱子為C40。樓梯采用現澆鋼筋混凝土板式樓梯,所用鋼筋為HRB335級,混凝土C25。樓板現澆鋼筋混凝土樓板,鋼筋HRB335級,混凝土C25。由于場地地質條件良好,基礎采用柱下獨立基礎。建筑內部設有三部樓梯,滿足防火要求。屋面排水采用自由落水。抗震設防烈度為7度。
【www.jiahaolighting.cn】
本設計嚴格遵守我國現行規范和有關規定,計算中包括荷載匯集,地震作用,風荷載,內力組合,樓板設計,基礎設計,樓梯設計等。其中水平地震作用的計算的方法采用底部剪力法,采用修正后的反彎點法(D值法)確定柱子的反彎點和內力。計算豎向荷載作用時采用彎矩的二次分配的方法。
本設計特點:合理選型,在滿足使用功能的同時,安全可靠,經濟合理。
關鍵詞:鋼筋混凝土;框架結構;內力分析
Abstract
The office building with the main structure of reinforced concrete frame structure, column net size of 4.8m × 6m, the total length of 59.57m, the total width of 15.77m, the total height of 24.25m, covering an area of 939.42 square meters, the total building area of 5522.139 square meters, a total of five, first floor floors are 3.9m, the remaining layers storey 3.6m.
Hollow brick wall with 300mm thick concrete block; staircase to 200mm solid block wall; walls with 200mm thick hollow concrete block. Columns with 450mm × 450mm square columns, the columns on each floor as the section size. Beam section height determined by its span, taking into account the construction of facilities, side span girder size 250mm × 500mm, the Span × 400 mm by 250 mm,no sub-beams, used for the HPB235 and HRB335 grade steel , slab concrete, C30, column for the C40. Staircase staircase with cast reinforced concrete slabs, used as HRB335 grade steel, concrete C25. Place reinforced concrete floor slab, reinforced HRB335 level, concrete C25. Geological conditions as well, based on an independent basis with the next column. With three stairs inside the building to meet fire safety requirements. Roof drainage with an organized drainage. Seismic intensity of 7 degrees.
The design of the existing norms and strict compliance with the relevant provisions of China, including load calculations together, earthquake, wind load, the internal force mix, floor design, foundation design, staircase design. In which the role of horizontal seismic base shear calculation method used, using the corrected inflection point method (D value) to determine the pillar of anti-bend point and the internal force. When calculating the vertical load distribution using the method of secondary moment.
The design features: a reasonable selection, while meeting the use of functional, safe, reliable, economical and reasonable.
Key words: Reinforced concrete; Frame construction; Internal force analyzing.
2.2 設計內容、建筑面積、標高
2.2.1 本次設計的題目為“辦公樓”。
2.2.2 建筑面積:5522.139m2,場地面積:120×150m,建筑共六層,首層層高為3.9m,標準層層高為3.6m。
2.2.3 室內外高差0.450m,室外地面標高為-0.450m。
2.3結構設計說明 內容來自www.jiahaolighting.cn 咨詢QQ:306826066
2.3.1 本工程為鋼筋混凝土現澆框架結構。外墻300mm厚空心磚墻,內墻(除廁所外)均為200mm厚空心磚墻。
2.3.2 本工程抗震設防烈度為7度,設計地震分組為第一組,設計基本地震加速度值為0.10g。
2.4各部分工程構造
2.4.1屋面:為不上人屋面
3.1建筑概況
該工程為永久性建筑,共六層。總建筑面積:5522.139M2,建筑占地面積:920.3565m2,樓內3部樓梯。建筑場地面積120×150㎡,柱網尺寸見建筑圖。
3.2.3 材料情況:
非重承空心磚:砂漿等級為M5;
混凝土:C25(梁、板、基礎)、C30(柱)
縱向受力鋼筋:HRB335級(柱);HRB335級(梁);箍筋:HPB235級鋼筋
3.2.4 抗震設防要求:設防基本烈度為7度,設計地震分組為第一組,設計基本地震加速度值為0.10g。
3.2.5 結構體系:現澆鋼筋混凝土框架結構。
3.2.6 施工:梁、板、柱均現澆。
3.3一榀框架選擇(見圖3-1)






目錄
第一章 前言 8
第二章 方案論述 9
2.1 設計依據 9
2.1.1 9
2.1.2 9
2.2 設計內容、建筑面積、標高 9
2.2.1 9
2.2.2 9
2.2.3 9
2.3結構設計說明 9
2.3.1 9
2.3.2 10
2.4各部分工程構造 10
2.4.1 10
2.4.2 10
2.4.3 10
2.5建筑材料選用 10
2.6建筑方案設計論述 10
2.7結構方案設計論述 13 版權所有www.jiahaolighting.cn 咨詢QQ:869918441
第三章 結構設計基本條件 15
3.1建筑概況 15
3.2結構概況 15
3.2.1 15
3.2.2 15
3.2.3 16
3.2.4 16
3.2.5 16
3.2.6 16
3.3一榀框架選擇 16
第四章 荷載匯集及截面尺寸的選取 17
4.1荷載匯集 17
4.1.1 17
4.1.2 18
4.2截面尺寸選取 18
4.2.1 18
4.2.2 18
4.3計算簡圖及層數劃分 18
4.4各層重力荷載代表值計算 19
第五章 水平地震作用下的框架變形驗算和內力分析 21
5.1梁線剛度 21
5.1.1 中框架 21
5.1.2 邊框架 22
5.2柱線剛度 22
5.3柱的抗側移剛度 22
5.4水平地震作用分析 23
5.4.1 23
5.4.2 25
5.4.3 26
5.4.4 27
5.4.5 28
5.4.6 28
第六章 風作用下的框架內力分析 29
6.1風作用下荷載匯集 30
6.2風作用下內力分析 30
第七章 框架在豎向荷載作用下的內力分析 32
7.1豎向荷載計算 33
7.1.1 33
7.1.2 33
7.2豎向荷載下框架計算簡圖 34
7.3豎向荷載作用下梁固端彎矩 34
7.3.1 34
7.3.2 35
7.4內力分配系數計算 35
7.4.1 35
7.4.2 35
7.5彎矩分配與傳遞 36
7.5.1 36
7.5.2 38
7.6梁端剪力 42
7.6.1 42
7.6.2 42
7.7柱軸力和剪力 43
7.7.1 43
7.7.2 44
第八章 內力組合 45
8.1框架梁內力組合 46
8.1.1 46
8.1.2 50
8.2框架柱內力組合 59
8.2.1 59
8.2.2 60
8.2.3 60
第九章 結構構件設計 68
9.1框架梁的設計 68
9.1.1梁的正截面配筋計算 68
9.1.2梁的斜截面配筋計算 74
9.2框架柱的設計 79
9.2.1柱的正截面配筋計算 79
9.2.2柱的斜截面配筋計算 82
9.3框架標準層板的設計 84
9.3.1設計荷載 84
9.3.2計算跨度 85
9.3.3彎矩計算 85
9.3.4板配筋計算 86 【本文來自56doc.com QQ:869918441】
9.4樓梯配筋 87
9.5基礎配筋 92
第十章 施工組織設計 115
一、編制依據及原則 115
1、編制內容及范圍 115
2、編制依據 115
二、工程概況及施工特點 115
1、工程概況 115
2、主要項目工程量 115
三、施工方案 116
1、施工程序及流向 116
2、施工順序 116
3、主要項目施工方法及施工機械 117
四、施工進度計劃 121
1、劃分工序項目及計算其工程量 121
2、計算所需勞動量及機械臺班數 121
3、編制施工進度計劃表 121
五、施工平面布置 122
六、保證質量,降低成本,安全文明施工,雨季施工等技術組織措 122
1、工程質量保證措施 122
2、安全文明施工保證措施 122
本文來自www.jiahaolighting.cn 咨詢QQ:869918441
3、雨期分項工程施工措施 124
七、保修及定期維修服務措施 124
結論
參考文獻
謝 辭
本文來自www.jiahaolighting.cn 咨詢QQ:869918441